ARAG Rip Master

Automatic depth control and slip monitoring for ripping and tillage equipment.

How It Works

Rip Master measures wheel slip and adjusts your ripper depth for you, through your tractor’s SCV with no extra valves. Set your depth and slip limits. It eases off in hard ground and digs back in when it can. Every pass is logged to a ripped depth map.


Simply set your desired depth and acceptable wheel slip and the Rip Master will ensure your implement is ripping at full depth within your working parameters at all times. Compatible with all ripping and tillage equipment.

Ripmaster: reads the slip, sets the depth Tractor GPS speed, wheel speed and the tyne depth sensor feed the Ripmaster controller, which drives the tractor's existing SCV. At low slip the tynes rip deeper, at normal slip they hold target depth, and at high slip the target depth is reduced. RIPMASTER · ISOBUS DEEP RIPPER CONTROL Reads the slip. Sets the depth. Tractor inputs GPS ground speed Wheel speed (ISOBUS) Tyne depth sensor NO EXTRA GPS RECEIVER Ripmaster IBX100 controller Wheel slip 6% Wheel slip 2% Wheel slip 13% Tractor's existing SCV 123 NO EXTRA VALVE BLOCK Hydraulic response Ripper depth cylinder Working depth 22 cm ↓ deeper 28 cm ↑ lifting HOLD TARGET DEPTHSlip above threshold RIP DEEPERLow slip: traction to spare REDUCE TARGET DEPTHHigh slip threshold reached PTS AG · ptsag.com.au

Benefits

  • Reduced fuel use
  • Reduced Trac/Tyre Wear
  • Reduced Implement/Machine Wear/ Damage
  • Record actual worked depth 

Features

  • Slip Control
  • Adaptive Depth Control
  • Headland Control
  • Ripped Depth Mapping
  • Fully ISOBUS and TASK CONTROL compatible  
  • VRT Ripping

Compatible Equipment

PTS AG fits and supports Rip Master on a wide range of ripper and tractor combinations, including:

  • Rippers: Nu-fab, Bednar, Gessner, Horsch Tiger, Top down and most other ripping and tillage implements
  • Tractors: CNH (Case IH / New Holland), Fendt, Claas, Challenger and John Deere

Not sure if your rig is covered? Get in touch and we'll confirm fitment for your specific ripper and tractor.

Rip Master FAQ

How it works

How does Rip Master know the slip %?

It compares GPS speed with the tractor’s transmission speed, which it reads over ISOBUS. The difference between the two is the slip %.

How does it know the depth of the tynes?

A position sensor on the implement’s depth wheel is calibrated to the tynes’ working depth.

Does it need an extra GPS receiver on the implement?

No. It uses the GPS already on your tractor. Depth comes from the position sensor.

Products and features

Do I need extra valves?

No. Rip Master controls your tractor’s SCV directly, so no extra valves are required.

Can it monitor pressure and RPM?

Yes. You can monitor 2 pressures and 1 RPM input.

Is disc downforce supported?

Yes. When the machine adjusts depth, it can adjust the discs too (where fitted). Active downforce uses 2 preset pressures to keep the discs working properly.

Is tilt control supported?

Yes. On machines with active tilt (such as Gessner), a second sensor is fitted and calibrated so the machine stays level at all heights. Tilt trim buttons on the home page let you fine-tune it.

Sales and support

Can I buy this across WA?

Yes. Local resellers across WA install and support it. Contact us to find your nearest one.

Who supports the product?

Your local reseller, backed by ARAG Australia and ARAG internationally.

Compatibility

Does it work with my current screen or GPS?

Yes. Rip Master is fully ISOBUS compliant, so it works with any ISOBUS screen. Task Control is needed for depth mapping and variable-rate (VR) ripping, and some screen brands need an unlock for it. Common screens include:

  • Case IH Pro 700 / 1200
  • Ag Leader InCommand / Go
  • New Holland IntelliView 4 / 12
  • John Deere GS4 / GS5
  • Trimble GFX-750 / 1050 / 1060 / 1260
Does it fit my current implement?

Almost certainly. We have retrofit kits for many popular machines in WA, and generic kits that adapt to most others.

Where can I get user guides?

Guides and quick reference sheets will be on our website soon. Until then, contact us and we’ll send them.